DIY Tub Installation.
DIY Tub Installation.
Blog Article
We've encountered this great article pertaining to How to Install a Bathtub Yourself directly below on the internet and concluded it made sense to share it with you here.
Installing a bathtub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is easily available, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and position the new bathtub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the brand-new one. See to it you have actually certified yourself for the job and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have actually already bought a brand-new bathtub and do not require to alter the arrangement of your previous water pipelines.
Your tools and product checklist should consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Turn on the supply of water and check all joints and new pipework for leaks and also tighten them if essential. Load the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its last position.
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can crack fairly very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about How to Install a Bathtub Yourself. Thanks a lot for finding the time to browse our post. Liked our write-up? Please share it. Let other people discover it. Thank you for going through it.
Estimating Report this page